Dissertations

18. Yunxia Chen, “Fabrication of Sensor-Embedded Heterogeneous Brain Simulant for the Evaluation of Impact-Induced Mild Traumatic Brain Injury,” Ph.D. Dissertation, University of Florida, Gainesville, FL, December 2024.

17. Bing Ren, “Sacrificial Ink-Assisted Embedded 3D Printing of Perfusable Channels for the Creation of Thick Vascularized Tissues,” Ph.D. Dissertation, University of Florida, Gainesville, FL, May 2024

16. Kaidong Song, “Study of Gelatin Microgel-Assisted Extrusion Fabrication System for 3D Bioprinting,” Ph.D. Dissertation, University of Florida, Gainesville, FL, August 2022.

15. Marc Sole Gras, “Vapor-Induced Phase Separation-Assisted 3D Printing of Polymeric and Metallic Structures,” Ph.D. Dissertation, University of Florida, Gainesville, FL,  August 2022.

14. Ashley M. Compaan, “Design of Inks and Printing Media for Advanced 3D Printing Applications,” Ph.D. Dissertation, University of Florida, Gainesville, FL, May 2019.

13. Ruitong Xiong, “Laser-based Bioprinting of Cellular Constructs and Applications for Organ-on-a-Chip Device Fabrication,” Ph.D. Dissertation, University of Florida, Gainesville, FL, August 2018.

12. Yifei Jin, “Study of Nanoclay-Assisted Extrusion Fabrication System for 3D Printing,” Ph.D. Dissertation, University of Florida, Gainesville, FL, May 2018.

11. Kyle Christensen, “Layer Formation and Deformation Compensation during Inkjet Printing of 3D Biological Structures,” Ph.D. Dissertation, University of Florida, Gainesville, FL, December 2017.

10. Brian Davis, “Study of the Dynamic Material Behavior and its Correlation to the Chip Formation Mechanism and Chip Morphology during Machining,” Ph.D. Dissertation, University of Florida, Gainesville, FL, May 2017.

9. Zhengyi Zhang, “Study of Printing Mechanism and Printing-Induced Cell Injury during Laser Printing,” Ph.D. Dissertation, University of Florida, Gainesville, FL, August 2016.

8. Fan Yang, “Design of Reliable and Sustainable Wireless Sensor Networks: Challenges, Protocols and Case Studies,” Ph.D. Dissertation, Clemson University, Clemson, SC, May 2015.

7. Changxue Xu, “Inkjet Printing of Three-Dimensional Vascular-Like Constructs from Cell Suspensions,” Ph.D. Dissertation, Clemson University, Clemson, SC, May 2014.

6. Jun Yin, “Fabrication of Grooved Hollow Fiber Membrane for Nerve Regeneration: Process Modeling and Performance Evaluation,” Ph.D. Dissertation, Clemson University, Clemson, SC, December 2011.

5. Yafu Lin, “Pulsed-Laser Direct Writing of Biological Materials,” Ph.D. Dissertation, Clemson University, Clemson, SC, December 2010.

4. Lei Tang, “Packet Error Rate Predictive Model for Sensor Radios on Fast Rotating Structures,” Ph.D. Dissertation, Clemson University, Clemson, SC, December 2010.

3. Wei Wang, “Modeling of Cell Transfer and Process-Induced Cell Damage in Laser-Assisted Cell Direct Writing,” Ph.D. Dissertation, Clemson University, Clemson, SC, August 2010.

2. Xiaoyu Wang, “Architecture Optimization, Training Convergence and Network Estimation Robustness of a Fully Connected Recurrent Neural Network,” Ph.D. Dissertation, Clemson University, Clemson, SC, May 2010.

1. Yu Long, “Modeling of the Effect of Tool Wear on Cutting Forces in Turning,” Ph.D. Dissertation, Clemson University, Clemson, SC, May 2008.

0. Yong Huang, “Predictive Modeling of Tool Wear Rate With Application To CBN Hard Turning,” Ph.D. Dissertation, Georgia Institute of Technology, Atlanta, GA, October 2002.